臭氧氧化-循环喷淋法处理钨钼选矿废水

采用臭氧氧化-循环喷淋法去除钨钼选矿废水中COD,研究了pH值、臭氧流量、循环频率对COD去除效果的影响。结果表明: 废水COD去除率随pH值、臭氧流量、循环频率增大而增加,在pH值为10、臭氧流量3.0 L/min、循环频率4.0次/min条件下,氧化120 min后废水COD含量由131 mg/L降至11.5 mg/L,COD去除率达91.2%,满足《污水综合排放标准》(GB 8978-1996)一级标准。与O₂、NaClO处理废水COD的对比试验结果表明,循环喷淋法结合O₃表现出较好的COD去除效果。     

海水淡化用空心锥喷嘴喷淋性能理论及实验研究

设计开发一种具有高通量、低流阻特征的空心锥喷嘴,并通过理论与实验方法研究空心锥喷嘴的喷淋性能,基于准自由涡理论建立空心锥喷嘴内部流体流动的数学模型,阐明流量系数、喷淋锥角、喷嘴流量与喷嘴结构参数之间的定量关系,并利用多效蒸馏海水淡化喷淋实验台对理论计算结果进行实验测试和验证。研究结果表明:正常工作状态下喷嘴流量系数、喷淋锥角、喷淋流量等参数理论值与测量值之间的误差小于5%,验证了设计模型的准确性。同时根据实验测试数据,拟合得到该类型空心锥喷嘴喷淋锥角与雷诺数之间的经验公式,可为蒸馏海水淡化用大流量空心锥喷嘴的结构设计、工艺选型提供理论指导和数据支持。     

H13钢等离子堆焊Ni60A/Cr3C2覆层的磨损及热疲劳性能

采用等离子堆焊技术在H13钢基体表面上制备了Ni60A/Cr₃C₂堆焊覆层,研究了覆层的磨损行为和热疲劳性能。在600 ℃下销盘试验的结果表明,镍基碳化铬复合覆层的耐磨性是Ni60A堆焊覆层的2.8倍和基材H13钢的11.6倍。镍基覆层可以显著降低H13钢的摩擦因数,加入碳化铬则会削弱覆层的摩擦性能。随着磨损的进行,主要磨损机理从氧化磨损演变为磨粒磨损和粘着磨损。在800 ℃到室温下的热疲劳测试结果表明,镍基碳化铬复合覆层在48个热循环后疲劳裂纹达到200 μm,早于镍基覆层的62次。这说明高温氧化促进热疲劳裂纹的产生。碳化铬增强相从镍基上剥离,导致镍基复合覆层热疲劳性能下降。     

Impact of gas formation on the transfer of Ti and O from TiO2-bearing basic-fluoride fluxes to submerged arc welded metals: A thermodynamic approach

Gas-slag-metal equilibrium calculations are performed to investigate the transfer of Ti and O to submerged arc welded metals with increasing TiO₂ addition in basic-fluoride fluxes. The results indicate that activities of TiO₂ and Ti₂O₃ considering slag-metal reactions alone do not account for Ti transfer behaviors since TiF₃ gas tends to form and reduce Ti-oxide activities. Thermodynamic simulation indicates that consideration of gases is essential to improve the prediction accuracy of Ti and O concentrations.     

Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

新型胶轮机车运行方式在大坡度盾构隧道施工中的应用

在传统地铁隧道施工中,有轨机车为主要运输方式,近年来有少量项目采用多功能胶轮机车运送施工材料。本文依托莫斯科地铁第三换乘环线东段大直径盾构项目案例,介绍胶轮机车的结构特点、使用优势、弧面运行时的轮胎保护措施。实践证明,胶轮机车在地铁隧道施工中具有很好的技术经济性,改进后的运行方式使其在管片弧面运行时性能更稳定。     

Numerical modelling of a low power non-transferred arc plasma reactor for methane conversion

Thermal flow characteristics and the methane conversion reaction in a low power arc plasma reactor for efficient storage and transport of methane, which is the main component of shale gas, were simulated. The temperature and velocity distributions were calculated according to the type of discharge gases and arc current level by a self-developed magnetohydrodynamics (MHD) code and a commercial ANSYS-FLUENT code; the transport of chemical species was analyzed as including the chemical reactions of methane conversion. The simulated results were verified by the comparison of calculated and measured arc voltages with permissible low error as under 4%. Three C₂ hydrocarbon gases with ethane (C₂H₆), ethylene (C₂H₄), and acetylene (C₂H₂) were selected as the converted species of methane from experimental data. The mass fraction of C₂ hydrocarbons and hydrogen as the product of the conversion reaction at the reactor was also calculated. Those values show good agreement with the actual experimental results in that the major conversion reaction occurred in C₂H₂ and hydrogen, and the conversions to C₂H₆, C₂H₄, and hydrogen were minor reactions of methane pyrolysis conversion.     

热处理对等离子喷涂铁基非晶合金涂层微观结构和耐腐蚀性能的影响

采用等离子喷涂技术在Q235钢基体上制备Fe48Cr15Mo14C15B6Y2非晶合金涂层,之后对涂层进行200,300,500,600,700℃热处理,研究了热处理对涂层微观结构、耐电化学腐蚀性能和耐均匀腐蚀性能的影响。结果表明:随着热处理温度的升高,涂层的非晶含量降低,孔隙率先减小后增大,经300℃热处理后涂层的孔隙率最低,且低于未热处理涂层的;热处理后涂层中的晶体相主要包括α-Fe,Fe-Cr,Fe63Mo37,Fe3C等;随着热处理温度的升高,涂层的自腐蚀电流密度先减小后增大,经300℃热处理后,自腐蚀电流密度最小,涂层的耐电化学腐蚀性能最好;经过热处理后,涂层在NaCl溶液中浸泡31d后的单位面积质量损失减小,且热处理温度越高,单位面积质量损失越小,涂层的耐均匀腐蚀性能提高。